Cart - $0.00

You have no items in your shopping cart.

YouTube Facebook Twitter 855-255-5550 Email Us

SW-MOTECH Handlebar Barback Risers for Select Aprilia, BMW, Honda, Kawasaki, KTM, Suzuki, Triumph & Yamaha Motorcycles | 31mm Rise - 22mm Back (Discontinued)

SW-MOTECH Handlebar Barback Risers for Select Aprilia, BMW, Honda, Kawasaki, KTM, Suzuki, Triumph & Yamaha Motorcycles | 31mm Rise - 22mm Back (Discontinued)

SKU: LEH.00.039.152

This Item Is No Longer Available

Note: This product is no longer able to be ordered. Please view related products on the right side of this page for more gear & accessories that you may be interested in.

This set of SW-MOTECH Handlebar riser bar backs and top clamps provides a more upright, comfortable riding position by raising and retracting the original 7/8" (22mm) diameter tubular handlebar. No need to replace your handlebars - simply remove the original top clamp, place the riser between the handlebar and original bottom clamp, and install the replacement top clamp using included hardware. Barbacks increase handlebar height by 31mm and move them back 22mm, producing an overall handlebar displacement of 35.4mm (1.4") at a 45 degree angle from the original position.

This product has replaced LEH.00.039.132 and LEH.00.039.133 and offers a superior powdercoated finish while fitting a wider range of bikes.

When installed, there may be a slight gap between the bar riser and the top clamp. This gap allows the top clamps to be torque-tightened onto the bar riser to prevent the bar from spinning.

No change of control cables, wiring, or hoses is required for most motorcycle models for normal 20mm to 30mm handlebar risers, HOWEVER:

Barbacks offer significant additional displacement of the handlebars and are more likely to require modification of cable/wiring/hose slack after installation than are standard handlebar risers.

The installer should always check for adequate cable/wiring/hose slack after installing any handlebar riser!

Simply put, the amount of cable slack varies on factory bikes even within a single model and year due to slight differences in the way the lines/cables are routed through the bike. While 99.9% of all bikes will not need adjustment of cables to install handlebar risers, you should ALWAYS check for adequate slack after installation.

Available in powdercoated silver (s) or black (b).

Please follow all Torque Specifications to the letter Failure to do this will void warranty.

Read the review by WebBikeWorld!


  • Aprilia Pegaso 650 '05-'07
  • Aprilia Pegaso 650 Factory '91-'99
  • Aprilia RSV1000 Tuono '02-'04
  • BMW F650 Funduro '93-'00
  • BMW F650CS Scarver '02-'06
  • BMW F650GS '03-'06
  • BMW F650GS Dakar '00-'07
  • BMW K75 / C / RT / S
  • BMW F800ST '06-'12 - Temporarily remove front brake cable stay and ties during installation. ABS models require brakeline extension
  • BMW R80GS / ST '80-'87
  • BMW R100GS / PD
  • BMW K100LT / RS / RT
  • BMW R1100GS '94-'99
  • BMW K1100RS
  • BMW R1150GS '00-'04 -  Front brake line extension required
  • BMW R1150GS Adventure
  • BMW R1150R
  • BMW R1150R Rockster
  • BMW R1200R '07-'10
  • Ducati Multistrada DS620
  • Ducati Multistrada DS1000
  • Honda Varadero XL125V '01-'08
  • Honda CB250 Nighthawk
  • Honda CB450SC Nighthawk
  • Honda CB500 '93-'95
  • Honda CB500S '96-'03
  • Honda CBF500 '04-'06
  • Honda CB550SC Nighthawk
  • Honda CB599 / CB600F Hornet '98-'06
  • Honda CBF600N / S '04-'07
  • Honda CB650SC Nighthawk
  • Honda FMX650 '05-'07
  • Honda SLR650 / FX650 Vigor '96-'99
  • Honda CB700SC Nighthawk
  • Honda NT700V Deauville '98-'05 - Relocate front brake hose clamp on triple tree down 1.5 inches.
  • Honda CB750SC Nighthawk
  • Honda CB750 Sevenfifity '92-'03
  • Honda Africa Twin XRV750 '90-'03
  • Honda CB900F Hornet '02-'05
  • Honda CBF1000 '06-'09
  • Kawasaki Eliminator 125 '01-'09
  • Kawasaki ER-5 '96-'05
  • Kawasaki KLE500 '91-'05
  • Kawasaki ER-6f '06-'08
  • Kawasaki KLR650 '94-'01
  • Kawasaki Versys 1000 '11-'14
  • Kawasaki ZRX1100 '97-'01
  • Kawasaki ZRX1200R '01-'06 - Control cable extensions may be required.
  • KTM EXC Models
  • KTM 640 Adventure '98-'07
  • Suzuki DR200SE '08-'13
  • Suzuki DR-Z400S/E '99-'07
  • Suzuki GS500E '89-'06
  • Suzuki GS500F '04-'06
  • Suzuki GSF600 Bandit '94-'04
  • Suzuki GSF600 Bandit S '97-'04
  • Suzuki DL650 V-Strom / XT '04-'16 - ABS models require upper front brake line extension
  • Suzuki DR650SE '95-'98
  • Suzuki DR650SE '08-'17
  • Suzuki GSF650 Bandit / S '09-'13
  • Suzuki GSX650F '08-'15
  • Suzuki SV650 '98-'08
  • Suzuki SV650 '17
  • Suzuki GSX750 '97-'03
  • Suzuki SV1000 '03-'05
  • Suzuki GSF1200 Bandit / S '00-'06
  • Suzuki GSF1250 Bandit / S '07-'16
  • Suzuki GSX1400 '01-'06
  • Triumph Tiger 900 '93-'99
  • Triumph Speed Triple 955 '00-'05
  • Triumph Tiger 955i '00-'07
  • Yamaha DT125R '00-'04
  • Yamaha TDR125 '93-'98
  • Yamaha MT-03 '16-
  • Yamaha XT660R '04-
  • Yamaha XT660X '04-
  • Yamaha XTZ750 Super Tenere '89-'03
  • Yamaha TDM850 '91-'01
  • Yamaha TDM900 '01-'09
  • Yamaha XJ900S Diversion '94-'98
  • Yamaha FZ1 '05-'09
  • Yamaha FZ1 Fazer '00-'05
  • Yamaha FZS1000 Fazer '00-'05
  • Yamaha BT1100 Bulldog '02-'05
  • Yamaha XJR1200 '95-'99
  • Yamaha XJR1300 '98-'09

*Some Triumph models may need two additional M8x20 short-head attachment screws for attachment to handlebar mounts.

These handlebar risers will only fit standard handlebar mounts that are symmetrical and perpendicular to each other.

This riser will not fit bikes with oversize (1" or 28mm diameter) handlebars.

If your handlebar mounts don't look similar to those pictured on this page, please contact us before ordering to confirm that the item will fit your bike.

While installation of these barbacks is possible on many bikes, such installation sometimes requires rerouting or extending the original hoses or cables.

This riser will fit your bike if:

(1) Your bar mounts are symmetrical and parallel;
(2) Your bars are 7/8" outer diameter;
(3) You have two M8 (8mm-diameter holes with standard M8 thread pitch) threaded holes in each of your two bar mounts; and
(4) The distance between the two holes in a single bar mount is 31-37mm on center. The distance between the two bar mounts is not a factor.

LEH.00.039.113 barbacks have outside top dimensions of 52mm L x 20mm W. Hole spacing in the base is 25mm (inside-to-inside diameter) and 45mm (outside-to-outside diameter).

LEH.00.039.123 top clamps have outside dimensions of 52mm L x 20mm W x 21mm H. Hole spacing in the top clamp is 25mm (inside-to-inside diameter) and 45mm (outside-to-outside diameter).

Kit includes:
- barbacks (1 pair)
- top clamps (1 pair)
- four M8x30 screws
- four M8x25 screws .

Please follow all Torque Specifications to the letter Failure to do this will void warranty.

Handlebar Barback Riser Application Chart

Aprilia  Barback Riser  Notes
Pegaso 650 '05-'07  LEH.00.039.21000.S
Pegaso 650 Factory '91-'99  LEH.00.039.21000.S
RSV1000 Tuono '02-'04  LEH.00.039.21000.S
BMW  Barback Riser  Notes
F650 Funduro '93-'00  LEH.00.039.21000.S
F650CS Scarver '02-'06  LEH.00.039.21000.S
F650GS '03-'06  LEH.00.039.21000.S
F650GS Dakar '00-'07  LEH.00.039.21000.S
R1100GS '94-'99  LEH.00.039.21000.S
R1150GS '00-'04  LEH.00.039.21000.S
Front brake line extension required
R1200GS '08-'12  LEH.07.039.12200.S
R1200GS LC '13-'16  LEH.07.039.12601  
R1200GS LC Adventure '14-'16  LEH.07.039.12601  
R1200R '07-'10  LEH.00.039.21000.S
Honda  Barback Riser  Notes
Varadero XL125V '01-'08  LEH.00.039.21000.S
CB500 '93-'95  LEH.00.039.21000.S
CB500S '96-'03  LEH.00.039.21000.S
CBF500 '04-'06  LEH.00.039.21000.S
599 '98-'06  LEH.00.039.21000.S
CBF600N / S '04-'07  LEH.00.039.21000.S
FMX650 '05-'07  LEH.00.039.21000.S
SLR650 / FX650 Vigor '96-'99  LEH.00.039.21000.S
CB750 Sevenfifity '92-'03  LEH.00.039.21000.S
Africa Twin XRV750 '90-'03  LEH.00.039.21000.S
919 '02-'05  LEH.00.039.21000.S
CBF1000 '06-'09  LEH.00.039.21000.S
Kawaski  Barback Riser  Notes
ER-5 '96-'05  LEH.00.039.21000.S
KLE500 '91-'05  LEH.00.039.21000.S
Ninja 650R '06-'08  LEH.00.039.21000.S
KLR650 '94-'01  LEH.00.039.21000.S
Versys 1000 '11-'14  LEH.00.039.21000.S
ZRX1100 '97-'01  LEH.00.039.21000.S
ZRX1200R '01-'06  LEH.00.039.21000.S
Control cable extensions may be required.
KTM  Barback Riser  Notes
640 Adventure '98-'07  LEH.00.039.21000.S
950 Adventure '03-'06  LEH.00.039.20000
990 Adventure '06-'13  LEH.00.039.20000
990SMT '08-'13  LEH.00.039.20000
1290 Super Duke GT '17  LEH.00.039.20000
Suzuki  Barback Riser  Notes
DR200SE '08-'13  LEH.00.039.21000.S
DR-Z400S/E '99-'07  LEH.00.039.21000.S
GS500E '89-'06  LEH.00.039.21000.S
GS500F '04-'06  LEH.00.039.21000.S
GSF600 Bandit '94-'04  LEH.00.039.21000.S
GSF600 Bandit S '97-'04  LEH.00.039.21000.S
DR650SE '95-'98  LEH.00.039.21000.S
DR650SE '08-'17  LEH.00.039.21000.S
GSF650 Bandit / S '09-'13  LEH.00.039.21000.S
SV650 '98-'08  LEH.00.039.21000.S
GSX750 '97-'03  LEH.00.039.21000.S
SV1000 '03-'05  LEH.00.039.21000.S
GSF1200 Bandit / S '00-'06  LEH.00.039.21000.S
GSF1250 Bandit / S '07-'16  LEH.00.039.21000.S
GSX1400 '01-'06  LEH.00.039.21000.S
Triumph  Barback Riser  Notes
Tiger 900 '93-'99  LEH.00.039.21000.S
Speed Triple 955 '00-'05  LEH.00.039.21000.S
Tiger 955i '00-'07  LEH.00.039.21000.S
Yamaha  Barback Riser  Notes
DT125R '00-'04  LEH.00.039.21000.S
XTZ750 Super Tenere '89-'03  LEH.00.039.21000.S
TDM850 '91-'01  LEH.00.039.21000.S
TDM900 '01-'09  LEH.00.039.21000.S
XJ900S Diversion '94-'98  LEH.00.039.21000.S
FZ1 '05-'09  LEH.00.039.21000.S
FZ1 Fazer '00-'05  LEH.00.039.21000.S
FZS1000 Fazer '00-'05  LEH.00.039.21000.S
BT1100 Bulldog '02-'05  LEH.00.039.21000.S
XJR1200 '95-'99  LEH.00.039.21000.S
XJR1300 '98-'09  LEH.00.039.21000.S

Customer Reviews
Review by NY Rider
I just returned from a cross country trip where I put 4,800 miles on my 2014 Suzuki V-Strom 1000. I tried to install 2" risers, but didn't have sufficient cable to pull it off. These risers were the next best option. Installation was super easy. It literally took me 17minutes to install. With two people it probably takes LT 10 minutes. The risers worked well too. They raised the bar and pushed them back toward me too. This mad the ride much more relaxed by taking a little pressure off my arms and back. (Posted on 7/2/2016)
Review by Some Guy on a Bike
A definite improvement for me after installing on a GSX650F. Puts hands and posture in a more neutral position so there is less pressure on the wrists and shoulders. Glad I ordered them! (Posted on 5/25/2016)
Review by Guest
I had installed a set of standard SW-Motech risers and they were ok...but I still felt like I was reaching too far forward. I was look at a set of Rok Risers, but I didn't like the way they were mounted. Lo and behold, SW-Motech comes out with these beauties.
Install was super easy; 10 minutes tops. No issues with stock cable lengths. Fit & finish is top notch.
The best part? Now my bike fits perfect. No more aching shoulders or stiff elbows. There is still enough lift to be comfortable when standing up on the pegs.
Just another quality product from SW-Motech and Twisted Throttle. You guys rock!!! (Posted on 4/27/2016)
Review by Jeffro206
Looked at several different risers and bar back sets, either didn't like the way they mounted or the rise was too high or far back to keep the cables and hoses stock. These mounted very well and didn't have to change anything else. Took quite a bit of pressure off my wrists when riding long distances. (Posted on 4/12/2016)
Review by marvin
makes riding so much more comfortable.just as advertised (Posted on 3/7/2016)
Review by Rand
The Honda NT700V is a great bike, but the bars are a bit low and forward to be comfortable for me on an all day ride. These work perfectly! No more lower back pain no matter how many miles! (Posted on 2/29/2016)
Review by jtbl
Need a rise and setback. This "universal" version fit my V7II bolt spacing and did not require changes to any cables on my bike. Just unbolt the existing bracket, have someone hold the bars while you fit the riser. Use some blue Loctite and torque to spec. (Posted on 2/2/2016)
Review by Strom rider
Advertised as exact fit. It does fit the handlebar, but does not allow the ignition switch to properly mount on the top clamp as the clamp is rounded with recessed nolt holes. (Posted on 1/19/2016)
Review by Patsfun62
Put these on my 2014 V Strom 1000 Adventure. Brake and clutch lines are very tight even with the ties and stays removed when moving the bars full left and right. May at least buy an aftermarket brake line in the future. (Posted on 1/13/2016)
Review by Cresty
Installed on a 2014 Honda CB 1100, no installation problems. Wish it was available in chrome, but the silver blended well with existing chrome. (Posted on 9/12/2015)
Review by Fauster
There's not much to say other than the machining of these riser barbacks was very and tgoodhe fit was perfect on my R1150R Rockster. The instructions were fine although installation was pretty straightforward. They look good, they fit, and they performed their intended use. There is less pressure on my hands and handling was not compromised. And I was still able to mount my SW-MOTECH accessory mount onto the top clamp. I'm happy. (Posted on 8/29/2015)
Review by Waterbuffalo74
Installed these on my 2007 Suzuki V-Strom 650 to make and handlebars highers, and to move them further away from me. Much better placement for the handlebars when I'm standing on the pegs, and when I'm sitting also more comfortable. (Posted on 7/8/2015)
Review by ken
i picked these up for my bike and yes ,they made a world of difference .they are easy to install with 'some' cable manipulation, I moved the hand controls in about a 1/4" on both sides, there is still a bit of tightness on one of the electrical cables at a full turn but the bars still lock and under normal riding conditions I don't see an issue. yes they're a hundred bucks but....worth it ! now if I can only find a 500 mile seat. ha!! (Posted on 6/10/2015)
Review by Dave
I just traded my 08 VStrom (DL 1000) on the 2015 model. I pretty much had my farkling done but was looking for a solution to get the handlebars up and back. The 2015 is different in that the front brake setup goes from hose at the reservoir to a steel union at the fender affording very little slack to add bar back/risers. The clutch is about the terms of very little little extra room to work. found these bar backs that worked without having to change any hoses/cables. There is a very nice write up about this part on their site. I installed these and they worked perfectly.....I just removed the keepers under the fairing for a bit more slack. This was a huge deal......saved a whole lot of work. The part is high quality....SW expected. I hope this part gets listed specifically for the V2. (Posted on 6/10/2015)
Review by Belrix
I installed these Barbacks on my 2012 Honda NC700X and they moved the handlebars up and back to provide a very comfortable ride!

I did have to re-position the front brake line hose a little to provide enough slack, not a big deal at all. (Posted on 5/14/2015)
Review by AtomicWoodworker
Bought this riser/barback set to alleviate forward pressure on my hands at the grips of my VStrom 1000. Works exactly as advertised. Allows to ride more upright and even helps me stand up more comfortably. Great product for the price.

The only thing to watch out for are the RHS brake and throttle cables. Once installed, there is virtually no slack left in either one. Recommend loosening or repositioning a few of the cable brackets to give you more room to maneuver. (Posted on 5/7/2015)
Review by Superfunkomatic
The product was just as advertised. Came in the mail quickly. (Posted on 4/29/2015)
Review by Rocketman2300
Well made and great fit. Came with all the hardware and easy instructions. (Posted on 3/28/2015)
Review by kuyohtay
Unfortunately, I entered my 2009 Ducati MTS 1100S and these came up. They don't fit the large diameter tapered bars. Also, for the money, quality is just below average. If they fit, they would be functional, but the powder coating was thick and drippy. The castings are average. Should have been machined and anodized (black was my choice) Would not recommend unless you have no other choice. (Posted on 3/3/2015)
Review by Anonymous
They're priced awfully high, but their construction seems very good. These did exactly what they're supposed to do - rise the bar and move it back. Unfortunately it seems that I didn't need either. I would love to return them but in my stupidity I lost a plastic cap to one of the bolts and now am stuck with a $96 hunk of aluminum. So make sure you actually need a riser/barback before you order. (Posted on 7/7/2014)
Review by Scottness
Great bar risers. The color matches well to the bike and it does exactly what it says it should… That said, the pressure on my hands wasn't effected enough and I've had to order something different to get the weight off my hands. If you are 5'6" or taller and are looking to alleviate pressure from your hands, this product isn't for you. Otherwise, it's awesome. (Posted on 7/7/2014)
Review by Robert
They're priced awfully high, but their construction seems very good. These did exactly what they're supposed to do - rise the bar and move it back. Unfortunately it seems that I didn't need either. I would love to return them but in my stupidity I lost a plastic cap to one of the bolts and now am stuck with a $96 hunk of aluminum. So make sure you actually need a riser/barback before you order. (Posted on 8/17/2013)
Write Your Own Review

Only registered users can write reviews. Please, log in or register