Cart - $0.00

You have no items in your shopping cart.

USD
YouTube Facebook Twitter 855-255-5550 Email Us

Oxford Heaterz Premium Adventure Motorcycle Heated Grips

$89.99
SKU: OXF.OF690Z

In stock


OR
 

The Premium line is Oxford's latest generation of heated grips. The Adventure version fits standard 7/8" handlebars and has ergonomically engineered grip pattern to optimize riding performance. Thicker rubber in areas of maximum wear; 5² block siped tread patterns for high levels of grip and feel; diamond tread pattern where maximum grip is required and a waffled area for finger-grip control.

Intelligent heat controller features:

  • 5 heat settings (30%, 40%, 50%, 75% and 100%) with LED lights to indicate heat setting
  • Sealed-for-life welded case for long-term durability and weather proofing
  • Battery Saving Mode turns grips off if you forget or if battery voltage falls too low
  • Raised and tactile silicone buttons for use with gloved hands

What's in the box:

  • Throttle and clutch side adventure pattern grips
  • Intelligent Heat Controller
  • Metal bracket and hardware for mounting controller
  • Wiring harness with 5 amp mini-blade fuse, zip-tys and grip glue
  • Instruction booklet and 2 year warranty card

Technical Specs:

  • Fits 7/8" (22mm) handlebars and tapered bars with 7/8" ends
  • Standard length 5.19" (132mm) Trimmable to 4.80" (122mm)
  • Grips are open ended to allow for bar-end weights and/or handguards
  • Current drain: Average 3.6 amps per pair (up to 2.0 amps each - 28-30 watts)
  • Fuse: 5 amp mini-blade (available in most auto parts stores)
  • Intelligent Heat Controller draws only 71 micro amps (0.071mA) in standby mode

Installation notes:

Requires only standard tools. No splicing, crimping or soldering needed. Connects direct to battery with ring terminals.

Also available: Oxford Premium Sports Heaterz and Oxford Premium Touring Heaterz

Customer Reviews
Review by ullmannp
Rating
I had a pair of these heated grips on another motorcycle with out the smart controller and they worked extremely well. So when the O.E.M heated grips failed I didn't have any reservations about buying the updated version of the Oxford adventure grips with the updated controller. The installation took only a half hour and they function perfectly. (Posted on 4/26/15)
Review by Akjohn62
Rating
I bought the adventure Oxford Grips for my dr350s. They work well and feel great. Two suggestions: if you buy new bars or throttle tube as I did, be aware that the grips will not slide over the knurling which is common on new stuff. I had to grind and sand the knurling down to slide them on. I have read reviews of folks beating them on with a 2x4. Can't recommend that. Also found the grips were about 3/4" long for my bars so I used a brass bushing on each side to extend the bar. I used a set of Zeta racing bar ends. They have a flat profile and the 35mm version matches the grip ends nicely. (Posted on 4/24/15)
Review by 11KLR
Rating
I have had the Oxford grips on my 2011 KLR650 for about 3 weeks now.
They heat up fast and even. Take your time putting them on the dry fit is very important to make sure you have them cut to the proper length.(if you want to keep the handlebar weights) I wish I had bought them sooner. (Posted on 2/17/15)
Review by 11KLR
Rating
I have had the Oxford grips on my 2011 KLR650 for about 3 weeks now.
They heat up fast and even. Take your time putting them on the dry fit is very important to make sure you have them cut to the proper length.(if you want to keep the handlebar weights) I wish I had bought them sooner. (Posted on 2/6/15)
Review by KerrvlleBob
Rating
Easy to install, controls are great and your hands are kept warm. Can't be much better. (Posted on 1/21/15)
Review by Scott
Rating
Installation was easy but wires came undone on 1st. (Posted on 1/19/15)
Review by John
Rating
I put these grips on my vstrom. I have rode year round for the past 25+ years. Wish I would have discovered these grips years ago. Work great, heat up quick. (Posted on 1/6/15)
Review by merway
Rating
I just couldn't see shelling out $250 for triumph grip heaters and decided to give these a try. They work as advertised and a whole lot cheaper. Hardware is top quality and looks good. It took about 3.5 hrs. to install. about 2 hrs. filing off the ridges on the throttle sleave. (Posted on 11/24/14)
Write Your Own Review

Only registered users can write reviews. Please, log in or register