Cart - $0.00

You have no items in your shopping cart.

YouTube Facebook Twitter 855-255-5550 Email Us

Rowe Electronics PDM60 - Power Distribution Module with User Programmable Cable


In stock


The future of power management......... is here.

The old methods of power distribution have gone the way of the floppy disk (remember those?).

No more checking or replacing fuses, or installing relays for powering high amperage electronics.

The PDM60 Power Distribution Module has 6 power circuits, making it easy to handle all your gadgets and farkles.The bright LED indicators keep you informed of the status of each circuit.

The PDM60:

  • Makes adding or removing aftermarket electrical devices / electronics (farkles) to your bike a breeze.
  • Is simple to install and simple to use.
  • Connects directly to the battery on your bike.
  • Has 6 power circuits to handle all your farkle needs.
  • Has bright LED indicators to keep you informed of the status of each circuit.
  • Eliminates the need to check or replace fuses.
  • Eliminates the need to install relays for powering high amperage electronics.

The PDM60 has been built with components selected for superior power management capability, and extended service life. It’s designed with one goal in mind: to provide years and years of superior, hassle free performance. The PDM60 unit is fully encapsulated to protect against rain, dust, humidity, etc. Whether it’s off-road, or cross-country via interstate, these units are built to last under the harshest of conditions..

Physical dimensions: 2”H x 3”W x .9”D; about the size of a business card, and less than an inch thick

6 indicator lights: The LEDs indicate the condition of the circuit.

  • GREEN, you’re good.
  • ORANGE, it’s an inactive or unused circuit, or has been interrupted due to an intermittent fault condition.
  • RED, you have an existing fault on the circuit, and the power has been interrupted.

Connecting to the unit: The PDM60 comes with a Posi-Lock connector for each circuit and the ground trigger. There’s also a Posi-Tap for connecting the ignition trigger wire. There’s one lead per circuit, two trigger wires, and the main power and ground leads. This makes the installation of the PDM60 a breeze, and allows for custom fitting the unit to your vehicle. Compact & easy.
A fuse in the power wire is not required, and would yield no additional benefit. The PDM60 is essentially a self monitoring digital fuse/breaker itself. The PDM60 has 60 Amps of power handling capability. Load it up.

For items requiring more than 15Amps: A 20A capable circuit (circuit #5) can be used to power intermittent applications like Stebel horns, etc. The 20A 
circuit is recommended for intermittent use only. If 20A is not enough, you can also run parallel circuits. You utilize two (or three) of the circuits (i.e. two 15A circuits=30A) to power your device. You just connect multiple circuit leads to your device power lead, ground your device to the frame or other suitable ground point, and you’re up and running, fully protected. Keep in mind that any load will be split equally among the circuits used, so each of the circuits used must be able to its portion of the total load. i.e. two circuits, 50% of total load each.

CAN type electrical systems: The unit is completely CAN type system compatible.

Programmable: The PDM60 is fully programmable. The dashboard software (free download) allows you to configure individual circuit behavior with a Windows compatible PC with .NET Framework 4 installed. There are 8 different triggering mode options for each circuit, and you can set delay activation / and delay off time periods, as well as individual circuit current limits. Configuration changes are a breeze to set up. The dashboard is easy to install, and easy to use. You can update/change your settings whenever you want.

Special Note: To program the PDM60, a Windows compabitle PC with .NET Framework 4 installed, is required.

Customer Reviews
Review by Slugo65
I bought and installed this on my Super Tenere right before a cross country road trip. This unit works exactly as described and allows you to program circuits for various loads and means of activation as needed. The reason I chose this particular unit was the fact that it features a dedicated 20 amp circuit that is perfect for running my stebel airhorn. The unit is impervious to moisture , dirt/ road filth and can handle complete immersion in water. The directions are simple and straightforward. The wires are labeled making connections simple if you follow the directions. In order to program the unit you will need a pc so be sure that whatever computer you use is windows compatible. I run an airhorn, heated seat, a circuit that powers my tank bag/ cellphone and GPS and that still leaves me with 3 circuits and 25 amps of juice for other stuff like heated gear and auxillary lights. I never have had any issues and the unit works as advertised. (Posted on 7/21/15)
Review by Andyks
Works as described. Fits in a tight place. Allowed me to tidy up the wires and get rid of old fashioned in line fuses. (Posted on 7/16/15)
Review by Blake
First off, I can't say that I'm completely impartial as I work for Rowe Electronics, the manufacturer of the PDM60. I can shoot it straight though. I've had nothing but positive feedback on this unit. We've tested units to over 1,000,000 cycles under a full 60 Amps of power. We've subjected them to all kinds of abuse. Fully submerging them, short circuiting them, you name it. They're rock solid and do a great job. We've had people use them on Motocrossers, Street Bikes, ATV/UTV, golf carts, tractors, race cars....even an ultralight aircraft. You won't be disappointed with the PDM60. (Posted on 1/29/15)
Write Your Own Review

Only registered users can write reviews. Please, log in or register