Originally conceived in Moto2 but now adopted by almost every motorcycle body worldwide (ACU; MSVR; MotoAmerica) and required for racing; the 'Lever Guard' was developed to help avoid the accidental engagement of the front brake lever during close wheel to wheel racing
The GIVI Z221 Replacement Rubber Bumpers are specifically made for the GIVI PL PLX side racks. These mushroom shaped pieces of rubber match the original bumpers that came with your side racks. Replace any lost or worn rubber bumpers to help keep your side case from rubbing against the metal pannier frames while you're out riding.
This MT Series DENALI 2-Pin Male Waterproof Connector Pigtail can be used to adapt other brands of lighting or accessories to the DENALI CANsmart Controller. The connector is pre-assembled with 3 inch 18 AWG wires exiting the connector which can be soldered onto the light or accessory of your choice.
These premium MT Series Waterproof Connectors are used in the DENALI 2.0 lights and harnesses. The kit includes both the male and female connector crimp-on terminals as well as waterproofing wire seals. Using an affordable crimping tool these connectors can be crimped onto wires in seconds to modify customize or replace electrical connections.
These premium MT Series Waterproof Connectors are used in the DENALI 2.0 lights and harnesses. The kit includes both the male and female connector crimp on terminals as well as waterproofing wire seals. Using an affordable crimping tool these connectors can be crimped onto wires in seconds to modify customize or replace electrical connections.
The Denali Interlink Pod Adapter allows you to link up to 4 Denali D1 Pods to each other with the integrated linking channel designed into the Denali D1 housing.
Are your micro / mini indicators flashing incorrectly?In many cases, after fitting micro / mini indicators, you will find that the indicators flash too fast or too slow. To stop this, R&G Resistors can be fitted which should solve the problem.** Supplied as a pair **These resistors are for the R&G Bulb Indicators. If you have R&G LED indicators, please use RGR0002
Are your led micro / mini indicators flashing incorrectly?In many cases, after fitting micro / mini indicators, you may find that the indicators flash too fast or too slow. To stop this, R&G Resistors can be fitted which should solve the problem.Note: We highly recommend buying this product when purchasing LED micro / mini indicators in order to save any disappointment when fitting.NO wire cutting or soldering is required, these resistors fit inline.** Supplied as a pair **These resistors are for the R&G LED Indicators. If you have R&G Bulb indicators, please use RGR0001
Choose Options
This product has multiple variants. The options may be chosen on the product page
Information
With this lens kit, you now have the ability to transform any CG2 Light Cannon or Optimus Series LED light to output a Selective Yellow beam versus the traditional white beam. Simply, remove the (4) bolts holding the bezel in place, swap in the new lens and you are ready to tackle the dusty trails. […]
Use this DENALI Wiring Adapter to easily connect a set of DRLs to a DENALI Auxiliary Light Harness or CANsmart Controller. The pass through design allows the DRL Lights to be added to the light circuit in addition to the Auxiliary LED Lights.
This DENALI MT Series 3-Pin Male waterproof connector pigtail can be used to adapt other brands of lighting or accessories to the DENALI CANsmart Controller or DENALI 2.0-series Premium Wiring Harness. The connector is pre-assembled with 3 inch 18 AWG wires exiting the connector which can be soldered onto the light or accessory of your choice.
These premium MT Series Waterproof Connectors are used in the DENALI 2.0 lights and harnesses. The kit includes both the male and female connector crimp-on terminals as well as waterproofing wire seals. Using an affordable crimping tool these connectors can be crimped onto wires in seconds to modify customize or replace electrical connections.
These 3-Pin Waterproof Blanking Caps can be used to cover and protect the unused leads of your DialDim Controller or CANsmart Controller. What’s In The Box? (x2) 3-Pin Waterproof Blanking Caps
These premium MT Series Waterproof Connectors are used in the DENALI 2.0 lights and harnesses. The kit includes both the male and female connector crimp-on terminals as well as waterproofing wire seals. Using an affordable crimping tool these connectors can be crimped onto wires in seconds to modify customize or replace electrical connections.
The DENALI power switch eliminator plug for 1st generation single & dual intensity harnesses replaces the original on/off button so your lights will automatically power on and off with the motorcycle's ignition. Enjoy the convenience of having your lights on anytime your bike is running and peace of mind knowing they will be off with the ignition. This handy eliminator plug is very easy to install, simply remove the power button that was included with the kit and plug the switch eliminator in. Designed and engineered in the USA. Simplify your 1st generation LED light kit with the power switch eliminator plug from DENALI!
This DENALI MT Series 3-Pin Female Waterproof Connector Pigtail can be used to to modify, customize, or replace electrical connections. The connector is pre-assembled with 3 inch 18 AWG wires exiting the connector which can be soldered onto the light or accessory of your choice. Note: Crimp-on 3-Pin Connector Sets are also available for purchase. What’s […]
Fits only Givi V46 and E52 topcases; not for other luggage case models. Keys can only be ordered as blanks and cannot be pre-cut by Givi to specific key numbers.
The DENALI Y-Splitter powers two DENALI B6 or DRL LED lights from one harness! Use it to remove the mess from your wiring and make installation a breeze. Plug-n-play connectors simply plug into both DENALI DRL/B6 lights (sold separately) which can then be tapped into your power source. Enhance your DENALI B6 / DRL installation and pick up a Y-Splitter before your next ride.
This Givi Z2711R Wrench is for tightening the bolt on PLR & PLXR rack brackets. Keep this in your toolbox for when you need it most. This wrench will allow you to work on your Givi PLR & PLXR rack.
The sew on patch worn by racers sponsored by R&G Racing is now available! Show R&G Racing support on leathers paddock jackets sweatshirts or anywhere you would like.
These premium MT Series Waterproof Connectors are used in the DENALI 2.0 lights and harnesses. The kit includes both the male and female connector crimp-on terminals as well as waterproofing wire seals. Using an affordable crimping tool these connectors can be crimped onto wires in seconds to modify customize or replace electrical connections.
This  D3 E-Mark & SAE/DOT Approved Hybrid Lens is an replacement for the hyrbid lens of a D2 light pod. What’s In The Box? (x1)  D3 E-Mark & SAE/DOT Approved Hybrid Lens
This D3 E-Mark & SAE/DOT Approved Fog Lens is an replacement for the fog lens of a D3 light pod. What’s In The Box? (x1) D3 E-Mark & SAE/DOT Approved Fog Lens
GET A PERFECT FIT: MONSOON EVO DIAMETER EXTENDER FOR RACKS WITH SLIGHTLY LARGER DIAMETERS With the Monsoon Evo Diameter Extender, we have developed a solution for mounting the Monsoon Evo on pannier racks with a slightly larger diameter than 18 mm. The extender is particularly suitable for powder-coated or otherwise machined luggage carriers where the […]
This DENALI Harness Extension can be used to extend the lead of your B6 or DRL light by 48 inches. Equipped with one male and one female miniature three-pin connector at each end the harness lovingly encircled in abrasion-resistant wrap for security and a clean-looking installation.
Use the DENALI wiring adapter for connecting DENALI B6 LED Brake Lights to the OEM KTM harness for a true plug & play connection. No wire tapping or other modifications to the original harness are necessary just plug directly into the factory connector to send the brake light signal from your motorcycle to the B6. This handy little adapter is all you need when connecting a B6 Brake Light to your KTM Adv...
This wiring adapter enables plug-&-play connection between our B6 Brake Light and the Honda Africa Twin 1100. To install, simply plug the white connector to the B6 and the remaining connector in line at the Africa Twin brake light. Click HERE to check out our pre-configured bundle that includes this adapter and a single or dual B6 brake light kit.Â
This Givi 4114KIT makes it possible to install the PLX4114 / PL4114 rack without the SR4114 top rack. No modifications are necessary for installation on the Versys. This kit comes with all necessary hardware and mounting instructions.
The Givi 03SKIT enables mounting of the Smart Bar or Smart Mount GPS holder to different motorcycles. Bike specific hardware replaces stock handlebar fasteners to fit the bikes listed below. Installation of this kit with the Smart Bar...
The Givi 04SKIT permits installation of the Smart Bar or Smart Mount GPS holder to certain motorcycles. Specific replacement handlebar hardware in this kit fits bikes listed below. With this kit you can mount the Smart Bar...
The Givi 02SKIT allows installation of the Smart Bar or Smart Mount GPS holder to specific motorcycles. Included replacement handlebar hardware fits the bikes listed below. The Givi 02SKIT and Smart Bar...
The Givi 05SKIT allows mounting of the Smart Bar or Smart Mount GPS holder to specific motorcycles. Replacement handlebar clamp hardware permits installation on the bikes listed below. Enjoy added versatility that the 05SKIT paired with the <stron...
Coated in vinyl rubber to prevent scratching the fender hooks are designed to grab the edge of fenders body panels and tanks when there is no frame for the loop straps to loop around. No need to buy all new straps the fender hooks loop into place on your existing straps.
Package contains four 2amp four 3amp two 5amp two 7.5amp two 10amp and one 15 amp fuses for use in the PowerHub2 Power Distribution Module by Denali. Fuses will work in other products that use mini ATM fuses.
This wiring adapter enables plug-&-play connection between our Rear T3 Switchback Turn Signals and the KTM 1290 Adventure R/S. To install, simply plug the 6-pin connector in line at the 1290 rear turn signals /brake light connector – then connect the T3s. Click HERE to check out our pre-configured bundle that includes this adapter, the rear T3s and the license plate […]
This wiring adapter enables plug-&-play connection between our B6 Brake Light and the Harley-Davidson Pan America 1250. To install, simply plug the white connector to the B6 and the remaining connector in line at the Pan America brake light. Click HERE to check out our pre-configured bundle that includes this adapter and a single or dual B6 brake light kit.
This wiring adapter enables plug-&-play connection between our front T3 light pods and the factory front turn signal harness in the Africa Twin 1100. The kit includes a pair of color-coded adapters so installation couldn’t be any easier. When using this adapter for the Africa Twin 1100, the T3s will run amber as a DRL (just like the factory turn […]
Includes bottom brakelight connector that attaches to a standard Givi Monokey or Monolock top plate as well as a wire to attach the connector to your motorcycle's wire harness.